Search found 45 matches
- Thu Jun 14, 2018 8:54 am
- Forum: General
- Topic: new bridgelux model? VESTA® 90CRI, 130lm/W
- Replies: 145
- Views: 24219
Re: new bridgelux model? VESTA® 90CRI, 130lm/W
I've just built a fixture using 8 one foot Vesta strips and two of the cheap Digikey Thomas Research drivers. All mounted on 25mm x 2.0mm aluminium square sections in a frame. Works out at 375mA per channel. One driver per colour channel means I have spectrum control. The amount of wiring required g...
- Thu Jun 14, 2018 8:38 am
- Forum: COBs & Other LEDs
- Topic: Parallel......
- Replies: 3
- Views: 687
Re: Parallel......
If you have a decent multimeter you can test the circuit and use the voltage adjustment knob to stop thermal runaway.
Then keep adding cobs and splitting current as funds allow.
Then keep adding cobs and splitting current as funds allow.
- Sat Jun 09, 2018 9:46 pm
- Forum: Strips
- Topic: Samsung's H562D connector rating?
- Replies: 1
- Views: 409
Re: Samsung's H562D connector rating?
Hi Eddie. You will be fine to slightly exceed the connector rating. Potentially you could solder to the strips directly if it is a concern though. The voltage rating on the connector is simply a reflection of the insulating properties of the connector material. Anything under 300v/9A is normal and c...
- Sun May 27, 2018 5:14 am
- Forum: General
- Topic: Hlg 600h-48a
- Replies: 1
- Views: 432
Re: Hlg 600h-48a
They are for remotely turning on/off the driver from an external input. Normally a voltage.
Seal them up with a heatshrink tail or throw a connector on them if not in use.
Seal them up with a heatshrink tail or throw a connector on them if not in use.
- Thu May 17, 2018 9:08 am
- Forum: General
- Topic: CV drivers?
- Replies: 8
- Views: 1111
Re: CV drivers?
I like them because its easier to load the driver to 100%. I always feel a CC driver has some wasted potential as you can never match the load to the max voltage output. They're also a good option if you want to scale up your light over time. Start with three cobs. Then go to four then to five. The ...
- Wed May 16, 2018 6:36 am
- Forum: COBs & Other LEDs
- Topic: Powering one vero 29 d
- Replies: 2
- Views: 663
Re: Powering one vero 29 d
That Vero would be more like 37.6v at 2.1A, so almost 80 watts. https://nz.mouser.com/ProductDetail/MEAN-WELL/ELG-100-36A?qs=sGAEpiMZZMt5PRBMPTWcaaMIEBR%2fZ8x2Ire1rMMCIGrLTLSO1kcbCw%3d%3d Sorry for the link to the NZ website - this A type driver has two pots so you can adjust the current and voltage...
- Mon May 14, 2018 7:50 am
- Forum: COBs & Other LEDs
- Topic: I have a 200 watt cxb3590 light will 4 cobs, should I add another 50 watt cob in the middle?
- Replies: 10
- Views: 1809
Re: I have a 200 watt cxb3590 light will 4 cobs, should I add another 50 watt cob in the middle?
200/9=22.2 watts per square foot - I'm thinking you're a little short on light there to get the results you're after.
Your light would look nice with a quantum board smack bang in the middle of it too.
Your light would look nice with a quantum board smack bang in the middle of it too.
- Sun Apr 15, 2018 6:11 am
- Forum: COBs & Other LEDs
- Topic: Dimmed high current driver vs lower current one
- Replies: 5
- Views: 1003
Re: Dimmed high current driver vs lower current one
To dim a driver normally means a slight loss in efficiency as the load decreases. Meanwell HLG's are VERY efficient but do run most efficiently at full; or close to full load. I'm not entirely sure I understand your question re: current otherwise. 2800mA is outside the efficacy range of those Cree's...
- Sat Apr 14, 2018 7:53 pm
- Forum: COBs & Other LEDs
- Topic: "Grow Factory"
- Replies: 14
- Views: 2310
Re: "Grow Factory"
Hey maaaaaate. Great to see another Kiwi on here DIYing. Strips might be the go for the vege/clone/mother areas but I would recommend COBs for your flowering area to get those HPS like frosty nugs. Especially given your 2 metres of headroom. Digikey and Mouser both do free shipping on orders over $6...
- Sat Apr 07, 2018 8:13 pm
- Forum: General
- Topic: Need A Sanity Check On A New Build
- Replies: 5
- Views: 799
Re: Need A Sanity Check On A New Build
Sounds like a good amount of light for a 3x3. I made do with less than 30w/sqft with good results for a short while. Using the light for dual purpose vege and flower, I would mix spectrums (some 3K and some 4K/5K) Straight 3500 just seems to lack the red to really drive flowering however this is com...