Search found 16 matches

by Astralou
Fri Jun 01, 2018 10:35 am
Forum: General Control & Automation
Topic: HLG-240-36B potentionmeter
Replies: 7
Views: 1299

Re: HLG-240-36B potentionmeter

Hi,

Thanks for your reply and help,

Well I do my best to understand :), could you look at my drawing and confirm that is what you mean ?
pot wire - Copie.jpg
Thank you :oops:
by Astralou
Thu May 31, 2018 11:47 pm
Forum: General Control & Automation
Topic: HLG-240-36B potentionmeter
Replies: 7
Views: 1299

Re: HLG-240-36B potentionmeter

Hi,

Thanks for your reply,

I've got 2wire from the HLG, and I've got what seems to be 6 slots on the potentiometer, where should I put the 2 wire from the drivers in the pot ?

Thank you very much all
by Astralou
Mon May 28, 2018 3:57 pm
Forum: General Control & Automation
Topic: HLG-240-36B potentionmeter
Replies: 7
Views: 1299

Re: HLG-240-36B potentionmeter

Thanks for your return, What to do with the 10k ohm resistor If i get it ? I think : When the pot in not wired the drivers turn at 100% so If I install an on/off switch for the pot then I just have to turn off the pot when i don't need it and the driver will automaticly run at full power ? (silly id...
by Astralou
Mon May 28, 2018 2:53 pm
Forum: General Control & Automation
Topic: HLG-240-36B potentionmeter
Replies: 7
Views: 1299

HLG-240-36B potentionmeter

Hello all, Hope you're fine, My project is almost done ! I'll get this driver HLG-240-36B and just need to put the right potentiometer to it: I have select 100kohm in the filter but don't know other criteria : ( I want be able to run the board at full power if I want to https://eu.mouser.com/Passive...
by Astralou
Sun May 27, 2018 6:59 pm
Forum: General Control & Automation
Topic: HLD driver help wiring the dimmer
Replies: 13
Views: 2181

Re: HLD driver help wiring the dimmer

Thank you for your replies : )

It comes with my driver, I'll keep it but not get it for my next driver (HLG-240H-36B)

I search for a potentiometer that will fit my 240h-36b :roll:

Thank you for your answer you helped me to find the right thing.
by Astralou
Fri May 25, 2018 3:18 pm
Forum: General Control & Automation
Topic: HLD driver help wiring the dimmer
Replies: 13
Views: 2181

Re: HLD driver help wiring the dimmer

I don't know, chinese dimmer with remonte from alibaba. no brand
by Astralou
Fri May 25, 2018 1:02 pm
Forum: General Control & Automation
Topic: HLD driver help wiring the dimmer
Replies: 13
Views: 2181

HLD driver help wiring the dimmer

Hello all,

Hope you're going well,

I need help to wire the dimmer with the HLG driver, so I am stuck, better wait than do a mistake :roll:

Thank you very much for your help, hope it can help other in the futur too.

++
by Astralou
Tue May 22, 2018 5:36 pm
Forum: Boards
Topic: Need advice 312led quantum board drivers
Replies: 18
Views: 2480

Re: Need advice 312led quantum board drivers

the board from Meiju 312 is low voltage "36" so for 2 of them u will need... HLG-240H-36V / A or B Or https://www.digikey.si/product-detail/en/mean-well-usa-inc/ELG-240-36A/1866-1532-ND/7703022 Thank you very much for your answer, yes it's meijiu 312. Well not HLG quality but took the shot, if need...
by Astralou
Tue May 22, 2018 6:30 am
Forum: Boards
Topic: Need advice 312led quantum board drivers
Replies: 18
Views: 2480

Re: Need advice 288led quantum board

Hello, THanks for all the reply, I go for 2x312boards LM561C S6, I think I'll use this driver HLG-240H-C2100B do you confirm it is ok ? I fear it's little low as board range is 540-145w for each for 312 ship on bard, maybe should I take another to be able to run it at full power if i want to ? Thank...
by Astralou
Wed May 16, 2018 9:08 am
Forum: Boards
Topic: Does anyone have any shenzen 288's
Replies: 8
Views: 2286

Re: Does anyone have any shenzen 288's

Bava used lm561y diodes. I wouldn't order from them. I just ordered fro. Feidaming. 40$ for single 80$ for double with no drivers. They seems to be a lower quality bin from a sphere test I seen but not by much. Will have them by next tuesday We stay in suspens, hope you got them and will be able to...