connecting Meanwell HLG-600h-48a with illumi MeshTek® 4 Channel PWM
Posted: Thu Feb 04, 2021 9:15 pm
hello everybody!
hope everybody is doing well?
first : im very bad on electric stuff so sorry if i say something seems you ridiculous ^^
second: im pretty on following instruction!![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
illumi meshtek is :
"The MeshTek® 4 Channel PWM Smart Lighting Controller (SLC) is a plug & play controller, providing an interface
between a standard non-dimmable LED driver(s) and LED load(s) thereby making an LED fixture/luminaire
smart. It can be configured to have four PWM controlled output channels for connection with LED load or four
PWM control signals from the MeshTek® module to interface with your external LED driver and then control
them remotely through MeshTek iOS and Android apps over a simple Bluetooth Low Energy (BLE) protocol.
Multiple lighting fixtures can be controlled individually or together as a group.
All PWM SLCs generate and form a reliable, secured and dynamic mesh network, extending the range as well.
Each SLC has a PA/SLA built in for high signal strength and sensitivity that can communicate to other SLCs up
to 200m range, requiring no external antenna, thereby saving costs in terms of material and assembly. The
patented PWM SLC technology also has a Real-Time Clock for time stamping and scheduling purposes."
![Image](https://image.noelshack.com/fichiers/2021/05/4/1612473155-mtdslc01.jpg)
![Image](https://image.noelshack.com/fichiers/2021/05/4/1612473155-mtdslc01-setup.jpg)
i meet problem to connect my illumi MeshTek® 4 Channel PWM to my driver Meanwell HLG-600h-48a
im confuse with the two output from the meanwell 600w driver.
picture of the driver with the 2 output:
![Image](https://image.noelshack.com/fichiers/2021/05/4/1612473148-slxolnz.png)
there is the plan:
-i have 10 ledstrip from cutter are 48v : 6 of them are 5000k nichia 757
4 of them are 2000k nichia 757
would love to connect those strip to my illumi meshtek and driver meanvell Meanwell HLG-600h-48a
- channel 1 : 5000k
- channel 2 : 2000k
i would love to be able to manage my 2k strip/ 5k strip independantly
i would love, if someone has time , and if it possible ,to show me wiring schema witch i will follow to connect everything right![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
its seems that i have to do something or some soldering with the illumi meshtek to allow it to play with high volt like meanwell 600w/48v , i think they are speaking about it in "page 7" of the illumi's manual , would you confirm me that?
there is the link to the illumi meshtek manual :
https://www.mouser.com/datasheet/2/834/ ... 625647.pdf
sorry if sometime my english is far from perfect, wish you a good day/nigh!
hope everybody is doing well?
first : im very bad on electric stuff so sorry if i say something seems you ridiculous ^^
second: im pretty on following instruction!
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
illumi meshtek is :
"The MeshTek® 4 Channel PWM Smart Lighting Controller (SLC) is a plug & play controller, providing an interface
between a standard non-dimmable LED driver(s) and LED load(s) thereby making an LED fixture/luminaire
smart. It can be configured to have four PWM controlled output channels for connection with LED load or four
PWM control signals from the MeshTek® module to interface with your external LED driver and then control
them remotely through MeshTek iOS and Android apps over a simple Bluetooth Low Energy (BLE) protocol.
Multiple lighting fixtures can be controlled individually or together as a group.
All PWM SLCs generate and form a reliable, secured and dynamic mesh network, extending the range as well.
Each SLC has a PA/SLA built in for high signal strength and sensitivity that can communicate to other SLCs up
to 200m range, requiring no external antenna, thereby saving costs in terms of material and assembly. The
patented PWM SLC technology also has a Real-Time Clock for time stamping and scheduling purposes."
![Image](https://image.noelshack.com/fichiers/2021/05/4/1612473155-mtdslc01.jpg)
![Image](https://image.noelshack.com/fichiers/2021/05/4/1612473155-mtdslc01-setup.jpg)
i meet problem to connect my illumi MeshTek® 4 Channel PWM to my driver Meanwell HLG-600h-48a
im confuse with the two output from the meanwell 600w driver.
picture of the driver with the 2 output:
![Image](https://image.noelshack.com/fichiers/2021/05/4/1612473148-slxolnz.png)
there is the plan:
-i have 10 ledstrip from cutter are 48v : 6 of them are 5000k nichia 757
4 of them are 2000k nichia 757
would love to connect those strip to my illumi meshtek and driver meanvell Meanwell HLG-600h-48a
- channel 1 : 5000k
- channel 2 : 2000k
i would love to be able to manage my 2k strip/ 5k strip independantly
i would love, if someone has time , and if it possible ,to show me wiring schema witch i will follow to connect everything right
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
its seems that i have to do something or some soldering with the illumi meshtek to allow it to play with high volt like meanwell 600w/48v , i think they are speaking about it in "page 7" of the illumi's manual , would you confirm me that?
there is the link to the illumi meshtek manual :
https://www.mouser.com/datasheet/2/834/ ... 625647.pdf
sorry if sometime my english is far from perfect, wish you a good day/nigh!