Page 1 of 1
Cutter SSK-1560
Posted: Fri Dec 06, 2019 5:57 am
by Millsie
I'm trying to build a kickass 300-400w supplemental flowering LED strip build for a friend down under
Currently researching Cutter's offerings but I'm finding an extreme lack of technical documentation?
I've found technix's postings over on RUI and have converted them to jpgs + attached them
I am sort of looking for more of the same sort of data (watts vs amps vs volts with umol, ppf)
I'm specifically looking at:
-SSK-1560-2790CR
-SSK-1560-730_660
Anyone know if there is any more data hanging around??
Re: Cutter SSK-1560
Posted: Fri Dec 06, 2019 6:12 am
by TEKNIK
I could show you some more, I don't have time to test all of cutters products as they have too many of them and technology changes all the time.
Re: Cutter SSK-1560
Posted: Fri Dec 06, 2019 8:26 pm
by Welight
If you could advise what the light would look like I can provide the data ie layout how many of each
Cheers
Mark
Re: Cutter SSK-1560
Posted: Sat Dec 07, 2019 3:32 am
by TEKNIK
Re: Cutter SSK-1560
Posted: Sun Dec 08, 2019 12:47 am
by Millsie
TEKNIK wrote: ↑Fri Dec 06, 2019 6:12 am
I could show you some more, I don't have time to test all of cutters products as they have too many of them and technology changes all the time.
That's all good mate
I'm generally looking to run SSK-1560-2790CR between 700ma to 1.2a
Welight wrote: ↑Fri Dec 06, 2019 8:26 pm
If you could advise what the light would look like I can provide the data ie layout how many of each
Cheers
Mark
The setup I'm looking to run 10 x SSK-1560's but I am a bit lost on drivers @ 48v
Would a HLG-480-c1400b suit the application with two parallel circuits of 5 x 1560?
or a series of 10 x 1560 @ 440-480v which is a bit ridiculous in my view and the max rated open circuit voltage on a hlg-480-c1400b is 420v?
Or would parallel of 10 x 1560's work on a hlg-480h-48b?
Cheers!
Re: Cutter SSK-1560
Posted: Sun Dec 08, 2019 9:47 pm
by Welight
Millsie wrote: ↑Sun Dec 08, 2019 12:47 am
TEKNIK wrote: ↑Fri Dec 06, 2019 6:12 am
I could show you some more, I don't have time to test all of cutters products as they have too many of them and technology changes all the time.
That's all good mate
I'm generally looking to run SSK-1560-2790CR between 700ma to 1.2a
Welight wrote: ↑Fri Dec 06, 2019 8:26 pm
If you could advise what the light would look like I can provide the data ie layout how many of each
Cheers
Mark
The setup I'm looking to run 10 x SSK-1560's but I am a bit lost on drivers @ 48v
Would a HLG-480-c1400b suit the application with two parallel circuits of 5 x 1560?
or a series of 10 x 1560 @ 440-480v which is a bit ridiculous in my view and the max rated open circuit voltage on a hlg-480-c1400b is 420v?
Or would parallel of 10 x 1560's work on a hlg-480h-48b?
Cheers!
At 1400ma(HLG-480-c1400b) you can run 5 boards in series at 226volts, so you could parallel those to get two strings of 5, at 226v per string at 700ma.
also certainly no problem to run 10 in parallel, that will give you 1 amp per board or approx 450watts, so will tap out the driver
Cheers
Mark
Re: Cutter SSK-1560
Posted: Tue Dec 10, 2019 8:32 am
by Millsie
Awesome thanks mate, I've just placed an order
Cheers for ya help