Hello all
It’s been a bit for me here. I have a few tents in the garage, I bought a 4pk of the 132s when the v2s sold out
I want to run 3 with 1 qb96 in a 2x4
Any driver advice?? 240 or 185??
3 qb132v1 n 1 solo 132
-
- LED-Curious
- Reactions:
- Posts: 12
- Joined: Wed Nov 15, 2017 5:54 pm
I want to run 3 with the 240 driver. I’m going to run the 36v like they suggest on their site.
Is anyone running them nearly maxed out at 75w ea??
I want to buy a 240 driver so I’m not pushing it all the way to get 210/220 total watts.
But a aluminum frame with something like this mounted - https://www.amazon.com/bayite-6-5-100V- ... 285&sr=8-5
Is anyone running them nearly maxed out at 75w ea??
I want to buy a 240 driver so I’m not pushing it all the way to get 210/220 total watts.
But a aluminum frame with something like this mounted - https://www.amazon.com/bayite-6-5-100V- ... 285&sr=8-5
-
- LED-Curious
- Reactions:
- Posts: 12
- Joined: Wed Nov 15, 2017 5:54 pm
I am going to run the last board separate on it’s on driver.
I got a hlg 65 in a trade and this last 132 on a 60w driver will help it out. I was using a HPS because of my climate but it’s not going to fly now
I have 2x2x4 that hlg 65 n 1, 132 will go into.
A 2x4x6 that has a qb96 on its own 185w driver and than I want to put the 3, 132s into
I need to get closer to the canopy and better heat management for the summer
I got a hlg 65 in a trade and this last 132 on a 60w driver will help it out. I was using a HPS because of my climate but it’s not going to fly now
I have 2x2x4 that hlg 65 n 1, 132 will go into.
A 2x4x6 that has a qb96 on its own 185w driver and than I want to put the 3, 132s into
I need to get closer to the canopy and better heat management for the summer
-
- LED-Curious
- Reactions:
- Posts: 12
- Joined: Wed Nov 15, 2017 5:54 pm
What 240 driver would I want to I use?
hlg-240h-36 or hlg-240-1750
Basically should I wire in a series or parallel..??
With the bay tech unit I want to get should I get a or b driver ??
hlg-240h-36 or hlg-240-1750
Basically should I wire in a series or parallel..??
With the bay tech unit I want to get should I get a or b driver ??
As techik has already stated they are two different voltages, so u can’t run them in parallel ,
Hlg 240 1750 will run all 4 qb132 boards or it will run 3 boards but will draw under 240 watts
The driver doesn’t have enough voltage to run 3+1 boards
Hlg240 1750 a onboard dimmer
Hlg240 1750 b external wires for external dimmer
Ab has both options
Hlg 240 1750 will run all 4 qb132 boards or it will run 3 boards but will draw under 240 watts
The driver doesn’t have enough voltage to run 3+1 boards
Hlg240 1750 a onboard dimmer
Hlg240 1750 b external wires for external dimmer
Ab has both options
-
- LED-Curious
- Reactions:
- Posts: 12
- Joined: Wed Nov 15, 2017 5:54 pm
The 4th board will be on its own. I have a 60w driver for it.
Was looking for help on which driver I should run the 3 of them on if I want to push them to 70 watts each.
Last, should I get a A or B driver if I am going to wire the bayite readout in the setup.
Was looking for help on which driver I should run the 3 of them on if I want to push them to 70 watts each.
Last, should I get a A or B driver if I am going to wire the bayite readout in the setup.