TEASER
Dimensions: 36"X18"X52"
Baltic Birch Plywood - stained and sealed
LED Dresser Stealth Build
Subbed
Want to Support the Site?
Use this Amazon referral link and any purchase you make within 24 hrs will earn LEDgardener a commission at no cost to you!
Use this Amazon referral link and any purchase you make within 24 hrs will earn LEDgardener a commission at no cost to you!
-
- LED Wizard
- Reactions:
- Posts: 1537
- Joined: Fri Apr 27, 2018 1:49 pm
Nice!
Do you have some plans for treating the wood against moisture?
Do you have some plans for treating the wood against moisture?
"Nothing is true, everything is permitted"
The wood was stained with walnut gel stain. Then protected with Varathane 1200 flat matte clear finish varnish
unkle_psycho wrote: ↑Sun Mar 24, 2019 12:36 pmNice!
Do you have some plans for treating the wood against moisture?
~finally legal
What's inside Part 2:
LED setup in Flowering Chamber
6 x Samsung F-Series Gen.3 3000k 2' LED strips (LT-F562B w/ LM561C diodes)= 432 LED's total.
Mounted on custom adjustable aluminum frame suspended with aircraft cable adjustable height.
Mean Well HLG-185H-24B Dimmed using 100K ohm linear potentiometer - Max output 4.8A with this setup
Voltmeter and ammeter displays DC output to LED's.
LED setup in Flowering Chamber
6 x Samsung F-Series Gen.3 3000k 2' LED strips (LT-F562B w/ LM561C diodes)= 432 LED's total.
Mounted on custom adjustable aluminum frame suspended with aircraft cable adjustable height.
Mean Well HLG-185H-24B Dimmed using 100K ohm linear potentiometer - Max output 4.8A with this setup
Voltmeter and ammeter displays DC output to LED's.
Last edited by GrowFOUR on Thu May 02, 2019 3:14 am, edited 1 time in total.
~finally legal
-
- LED Wizard
- Reactions:
- Posts: 1537
- Joined: Fri Apr 27, 2018 1:49 pm
So it has two sections, one small section for veg and a larger one for flower?
Is the idea for the switches and dimmer that you can decide which side is lit, and dim while vegging?
Is the idea for the switches and dimmer that you can decide which side is lit, and dim while vegging?
"Nothing is true, everything is permitted"
Yes there are TWO chambers inside the growbox, completely isolated from each other to avoid light leaks.
Since I can only grow FOUR plants at a time my plan is to have TWO in flower and TWO in veg and rotate. I would like to have a mother plant constantly in veg but then I would only be able to flower ONE at a time and I can get a quicker turn around with this schedule
Since I can only grow FOUR plants at a time my plan is to have TWO in flower and TWO in veg and rotate. I would like to have a mother plant constantly in veg but then I would only be able to flower ONE at a time and I can get a quicker turn around with this schedule
unkle_psycho wrote: ↑Wed Mar 27, 2019 11:09 amSo it has two sections, one small section for veg and a larger one for flower?
Is the idea for the switches and dimmer that you can decide which side is lit, and dim while vegging?
~finally legal
ESP8266 NodeMCU ESP-12E
Using phone app to control:
-ON/OFF + timer for veg and flower LEDs
-Unlocks front dresser door
-Flower LEDs light height adjust up/down
-Turn off air pumps (because the pump and bubbles are the loudest part of the system I can turn them off temporarily from my phone if need be) Also in the picture there is a temperature switch, currently measuring water temperature but not hooked up to switch anything. Under the microcontroller there is a 12V fan speed controller for one of the flower chamber fans. Future microcontroller add-ons for remote monitoring and control:
Temperature readings and logging for air humidity and temperature (using BME280 sensor module) as well as water temperature
Live feed camera in flower chamber
LED light height to plants (using VL53L0X Laser Ranging Sensor GY-530 Time-of-Flight (ToF) Ranging Module)
PWM for 12v fan speed control
PWM or 0-10v dimming for Mean Well driver
+ many more projects
Using phone app to control:
-ON/OFF + timer for veg and flower LEDs
-Unlocks front dresser door
-Flower LEDs light height adjust up/down
-Turn off air pumps (because the pump and bubbles are the loudest part of the system I can turn them off temporarily from my phone if need be) Also in the picture there is a temperature switch, currently measuring water temperature but not hooked up to switch anything. Under the microcontroller there is a 12V fan speed controller for one of the flower chamber fans. Future microcontroller add-ons for remote monitoring and control:
Temperature readings and logging for air humidity and temperature (using BME280 sensor module) as well as water temperature
Live feed camera in flower chamber
LED light height to plants (using VL53L0X Laser Ranging Sensor GY-530 Time-of-Flight (ToF) Ranging Module)
PWM for 12v fan speed control
PWM or 0-10v dimming for Mean Well driver
+ many more projects
Last edited by GrowFOUR on Sun Apr 14, 2019 2:00 pm, edited 1 time in total.
~finally legal