Lights aren't all that bright, can you help?
-
- LED-Curious
- Reactions:
- Posts: 2
- Joined: Sat Jun 23, 2018 4:15 am
I have recently built my own LED strip perimeter light for two of my tents. I did some research on reddit and came across a diy build and i copied his serials and bought the same things, I purchased 12 LED MOD FSERIES GEN3 3000K STRIP part number SI-B8V261560WW, and 2 Meanwell HLG-240H-C1750B drivers. I have them wired one into the other in a rectangle patter. I have 10k omh pot for dimming. i run 6 lights per driver. It was my understanding they are 23 watt strips and that i have a 240w driver. I would assume 23w x 6(lights)= 138watts more than enough power I would think but i'm a noob. I would definitely not say they are blinding by any means. compared to my blurples the light seems to only travel a few inches before dissipating, and advice would be super.
If you have a 10K ohm pot and that's not a typo, that's where your problem is. It needs to be 100K or you're only going to get 10% power. You can unhook it for max power also.OntarioGro17 wrote: ↑Sat Jun 23, 2018 4:23 amI have recently built my own LED strip perimeter light for two of my tents. I did some research on reddit and came across a diy build and i copied his serials and bought the same things, I purchased 12 LED MOD FSERIES GEN3 3000K STRIP part number SI-B8V261560WW, and 2 Meanwell HLG-240H-C1750B drivers. I have them wired one into the other in a rectangle patter. I have 10k omh pot for dimming. i run 6 lights per driver. It was my understanding they are 23 watt strips and that i have a 240w driver. I would assume 23w x 6(lights)= 138watts more than enough power I would think but i'm a noob. I would definitely not say they are blinding by any means. compared to my blurples the light seems to only travel a few inches before dissipating, and advice would be super.
Want to Support the Site?
Use this Amazon referral link and any purchase you make within 24 hrs will earn LEDgardener a commission at no cost to you!
Use this Amazon referral link and any purchase you make within 24 hrs will earn LEDgardener a commission at no cost to you!
-
- LED-Curious
- Reactions:
- Posts: 2
- Joined: Sat Jun 23, 2018 4:15 am
thanks guys i cut the bum ones off and boom so much brighter. I'm gonna order some 100k pots but to ne honesy i might just leave it, ?I was under the impression I had to have those wires hooked to a pot.
Good stuff. It’s fine to leave the dimming leads with nothing on them if you don’t want to change the pots.OntarioGro17 wrote: ↑Sat Jun 23, 2018 1:16 pmthanks guys i cut the bum ones off and boom so much brighter. I'm gonna order some 100k pots but to ne honesy i might just leave it, ?I was under the impression I had to have those wires hooked to a pot.
Want to Support the Site?
Use this Amazon referral link and any purchase you make within 24 hrs will earn LEDgardener a commission at no cost to you!
Use this Amazon referral link and any purchase you make within 24 hrs will earn LEDgardener a commission at no cost to you!
[quote=LEDG post_id=7368 time=1529732029 user_id=2
If you have a 10K ohm pot and that's not a typo, that's where your problem is. It needs to be 100K or you're only going to get 10% power. You can unhook it for max power also.
[/quote]
LOL...I must be getting better. As soon as I saw the one, 100K potentiometer, I "knowed" right away that was the problem!
If you have a 10K ohm pot and that's not a typo, that's where your problem is. It needs to be 100K or you're only going to get 10% power. You can unhook it for max power also.
[/quote]
LOL...I must be getting better. As soon as I saw the one, 100K potentiometer, I "knowed" right away that was the problem!